Industrial Robot Refurbishment

We have refurbished hundreds of Fanuc Robots. Our experience, facilities and access to parts enables us to deliver a robot that meets all OEM specifications and exceeds your expectations.

Our Refurbishment Process consists of:

Evaluation:

Robot evaluations consist of a pre-power up inspection of cables connectors, motor caps, fans, switches/pushbuttons, seals, proper PC board connections, loose items and other physical concerns which could potentially be problematic when power is applied. After which the robot will run a repeatability/durability/backlash test for a minimum of ten (10) continuous hours with a full payload, through full range of motions evaluating the robot’s ability to meet the OEM specifications of repeatability. This is followed by another inspection of mechanical and electrical components and a report of our findings is generated and provided to the customer.

​Refurbishment:

Our industry-leading refurbishment process covers every aspect of the arm/controller system to ensure the finished product meets all OEM specifications for durability and repeatability. A typical scope of work includes:

Controller
  • Clean inside and outside of controller cabinet
  • Clean heat exchanger
  • Inspect Controller for OEM Engineering Changes
  • Remove and clean all PCB’s
  • Clean connector contacts
  • Replace fan filters
  • Replace cooling fans (when applicable)
  • Replace batteries
  • Delete old files from memory board (optional)
  • Replace any missing covers
  • Paint Controller (optional)
  • Perform functionality test on Teach Pendant
  • Prepare for shipment
Mechanical
  • Clean mechanical unit
  • Disconnect all cable connectors
  • Clean all contact pins and plugs
  • Clean drive components
  • Replace lubricants per OEM specification
  • Master the robot (when applicable)
  • Paint Robot (optional)
  • Adjust over-travel limit switches (optional)
  • Install witness marks
  • Run a verification test of a minimum of fifty (50)
    cycles to confirm proper operation and cable connections prior to completion.

Robot Repair Process

Track a customer's R-2000iB progress through our refurbishment process:

robots-refurbishment-process-01

Before Refurbishment

This FANUC R-2000iB had seen a good bit of typical use, but was still a good candidate for refurbishment.

robots-refurbishment-process-02

Grease and Metal

The robot was covered in a mixture of grease and metal shavings.

robots-refurbishment-process-03

Chipped Paint

Years of wear has chipped and even removed much of the paint.

robots-refurbishment-process-04

Dirty Motors

Every exposed surface is coated in grime. Seems as if this guy has seen some action.

robots-refurbishment-process-05

Worn Dirty Cables

The cabling was worn and the protective coverings were in need of replacing.

robots-refurbishment-process-06

Cleaned and Prepped

Our refurbishment process begins with a thorough cleaning. Once clean, an inspection of all mechanical and electrical components can begin.

robots-refurbishment-process-07

RV

Axis 1 would not meet repeatability specs for backlash. Upon its removal small pieces of the gear assembly were found in the grease. It had to be replaced.

robots-refurbishment-process-08

Ready for Paint

The bodywork is complete and the robot is in the process of being prepped for paint.

robots-refurbishment-process-09

New Motors

All the motors were either replaced, repaired or repainted depending on the condition and need.

robots-refurbishment-process-10

Connections

All cable connectors are cleaned and inspected.

robots-refurbishment-process-11

After Refurbishment

With a fresh paint job in the original FANUC yellow – complete with black accents, this robot has a new lease on life. It is almost indistinguishable from a new robot.

robots-refurbishment-process-12

Ready to Ship

Complete with new arm tags and cable covers, the fully refurbished robot has been load tested to ensure it meets all OEM standards and is about to be bolted, banded and shipped back to a happy customer.

Our Refurbished Fanuc Robot Inventory

robots-refurbishment-ArcMate100iC
Arc Mate 100iC w/ R-30iB
robots-refurbishment-ArcMate120iC
Arc Mate 120iC w/ R-30iB
robots-refurbishment-LRMate200iC
LR Mate 200iC w/ R-30iA
robots-refurbishment-M-10iA
M-10iA w/R-30iA and R-30iB
robots-refurbishment-M-16iB
M-16iB/20 w/ R-30iA
robots-refurbishment-M-710iC
M-710iC/50 w/ R-30iB or R-30iA
robots-refurbishment-M-20ia
M-20ia w/ R-30iA or R-30iB
robots-refurbishment-M-900iA
M-900iA/260L w/ R-30iA
robots-refurbishment-M-900iA-350
M-900iA/350 w/ R-30iA
robots-refurbishment-M-900iA-400L
M-900iA/400L w/ R-30iA
robots-refurbishment-M-900iB
M-900iB/700 w/ R-30iB
robots-refurbishment-R-2000iA-125L
R-2000iA/125L w/ R-J3iB
robots-refurbishment-R-2000iA-165F
R-2000iA/165F w/ R-J3iB
robots-refurbishment-R-2000iB-100P
R-2000iB/100P w/ R-30iA
robots-refurbishment-R-2000iB-210F
R-2000iB/210F w/ R-30iA
robots-refurbishment-R-2000iB-125L
R-2000iB/125L w/ R-30iA
robots-refurbishment-R-2000iC-125L
R-2000iC/125L w/ R-30iB
robots-refurbishment-R-2000iC-165F
R-2000iC/165F w/ R-30iB
robots-refurbishment-R-2000iC-210F
R-2000iC/210F w/ R-30iB

Start Your Refurbishment

Quick Quote

Or Call today for a free,
no obligation quote 1-888-926-0737

Thank you Thank you for contacting TIE-FANUCWORLD. We are diligently working on your request and will respond shortly.

If you need to speak with one of our friendly and knowledgeable customer service representatives, please call (877) 876-3994, and we will be happy to assist you.

Our hours of operation are:Monday - Friday, 7:00 am - 7:00 pm Central TimeSaturday, 8:00 am - 12:00 pm Central Time.

We appreciate and value your business.

In a hurry?

The Part you are looking for is for sale online. Click the button below to buy now.